Notice For Metal-Forming Machinery (KSC033)
$33.36This safety tool is used to raise awareness of the dangers of metal-forming machinery in the workplace.
Showing 217–240 of 307 results
This safety tool is used to raise awareness of the dangers of metal-forming machinery in the workplace.
These versatile On-Off magnet-base shields can be used on lathes, drills, mills, grinders, or any equipment that has a flat, ferrous mounting surface. The heavy-duty magnetic base is 2 3/4-inch square with a V-groove and measures 3-inches high. The 200-lb holding force keeps the shield in place when the magnet is on. If an adequate…
The On/Off Magnetic Base Only With M12 Tap (FKT285) is designed to easily control the machine is a safe and non-hazardous manner for the worker.
Cutting/Turning and Forming/Fabricating Specific Operator Safety Signs are available in English, Spanish and French. Ex. “Never place your hands in this machine.”
This guard-opening sign is based on Table O-10 of OSHA 29 CFR 1910.217 for mechanical power presses, which shows the distances that guards shall be positioned from the point of operation based on opening size. This sign can be used by engineering, maintenance, etc., for reference when designing or fabricating guards. This 10″ x 12″…
This standard heavy-duty, single plunger run palm button provides one normally open and one normally closed contact arrangement. This 2 1/4″ button is mushroom-shaped. The palm button face plate has a solid neoprene gasket which provides an oil-tight seal upon installation. When applying two-hand control as a safeguard to any machine, fixture, device, etc., the…
Part No. CTK-004 Single-hub mounting box is used when wires terminate at this box. Part No. CTK-003 Double-hub mounting boxes are used when wires are required to go through the box and on to another mounting box. Part No. CTK-038 Deep single-hub mounting box is used when wires terminate at this box. Part No. CTK-039…
Stock positioner with screwdriver point with 90-degree bend to remove parts from die. Total Length: 14″ Weight: 2 1/2 oz.
Spare Plastic Conduit Adapter—M20 to 1/2″ (SIQSM20)
Pliers and tongs are used to keep hands out of the point of operation while feeding or removing parts from the machine. Pliers and tongs, like all hand-feeding tools, are not considered to be guards or devices by themselves. But these hand tools offer additional protection. Most of the tools are constructed of soft alloy…
The point-of-operation gauge is designed to be used as a quick reference tool to check for what OSHA regulations and ANSI standards refer to as safe-opening. It is a valuable tool to use during the design, installation, and inspection of guards to make sure the openings do not exceed 1/4″ (6 mm) for OSHA/ANSI and…
This portable welding screen offers protection for personnel who are in the area of welding and grinding work zones. The .4 mm-thick, semi-transparent PVC screen protects personnel from metal chips and sparks produced during the welding and/or grinding process. The red PVC screen pulls out easily from the mobile stand and attaches to a center…
Front and rear shields are available. NOTE: Milling Machine Chip Shields KYL019 and KYL059 are *Marked for Discontinuation* until inventory is depleted. Replacement transparent shields and mounting arms will be supported and supplied through January 1, 2024 or until inventory is depleted. Replacement Milling Chip Shields for KYL Series are the Protector Series Shields: Please…
Themilling machine control is designed for vertical milling machines that have a table motor. Each milling machine control is housed in a NEMA 12 enclosure that includes a disconnect switch, reversing magnetic main drive motor starter, a control relay for the table motor, and a 100 VA transformer that is generically numbered and wired to…
Press Brake Danger, Visual Safety Signs (KSC060-KSC060S) are designed for visual danger awareness. Sign are available in English and Spanish.
The Mill Replacement Shields are designed to replace existing shields that show signs of wear, to optimize safety. Product Manual Download the Product Manual PDF
Safety mats are available in numerous sizes, and are available with or without edging. This is a non-stock item and may incur an extended delivery time. Pressure-sensitive safety mats are intended to be used as auxiliary or additional safeguarding equipment to protect operators and other employees in the machine area. They must not be used…
Rear milling machine shield assemblies can be used to protect personnel from swarf and chips at the rear of the table on both sides of the machine column. They can be used on milling machines or other equipment that require these types of shields. The two 3/16-inch-thick polycarbonate panels are mounted to the frame of…
This heavy-duty, single plunger red emergency-stop palm button provides 1 NO and 1 NC contact arrangement. This 2 1/4″ button has a mushroom-shaped plunger with a spring latch that keeps the button latched down when pushed to meet NFPA 79. A release is incorporated. It also has provisions for attaching a padlock to the latch….
For Use With Nonreversing Motor Starters
This emergency stop button measures 4 1/2 inches by 3 1/2 inches by 3 inches. It is housed in a NEMA 12 metal enclosure. The emergency stop is self-latching; to reset the red button, turn it to the right.
Open Monday – Friday
8:00am – 5:00pm CST
To reduce risk and prevent workplace
injuries by becoming our customer’s trusted
advisor and source for machine safeguarding
training, assessment services, and provider
of turnkey engineered safeguarding solutions.
5795 Logistics Parkway
Rockford Illinois 61109
1-800-922-7533
Copyright 2023. All Rights Reserved By Rockford Systems LLC
Rockford Combustion Solutions provides fuel-train management and combustion-safety solutions for safety-conscious organizations that work with fuel-fired equipment in thermal processes.
Rockford Combustion
5795 Logistics Parkway
Rockford, Illinois USA 61109