Category: EX-AL Barrier & Perimeter Guarding
Showing all 23 results
-
Ejection Curtain Guarding Kits for Presses
$3,469.14 – $4,066.67Ejection Curtain Guarding Kits for Presses are designed for organizations that require a superior hydraulic press safety solution to help protect their employees and prevent injuries caused by flying, rolling or sliding debris. Most commonly used on H-presses or compacting presses that are hydraulic powered, the ejection curtains are coiled-wire fabric machine guards, widely used…
-
EX-AL™ Deadbolt Latch (FKT620)
$143.57A deadbolt latch is ideal for holding guard doors closed. This spring-loaded deadbolt is made of anodized aluminum. A socket-head locking set-screw located towards the end of the latch requires the use of a tool to open the guard. This feature complies with OSHA 29 CFR 1910.217 (c)(2)(d). This deadbolt with side latch includes all…
-
EX-AL™ Door Handle (TXS101)
$25.38Plastic, Direct T-Slot Frame, Door Handle (TXS101) – The plastic door handle is ideal for T-slot frame doors on guards or shields. Handles bolt directly to doors and panels using two 1/4-20 screws and two T-nuts (sold separately). The handle is made of high-strength black polycarbonate and is corrosion-resistant. When ordering a plastic door handle,…
-
EX-AL™ Door Stop (FKT595)
$39.15Aluminum, Direct Two-Bolt, Door Stopper (FKT595) – The door stop is made of aluminum and bolts directly to doors using two 1/4-20 screws and two T-nuts (sold separately). BHCS14C.5FCSB8 – 1/4-20 screw FSY028 – t-nut
-
EX-AL™ Hinges and Ball Lock Pin
$29.37 – $411.88Hinges are used to swing guard panels and segments to the right or left. They are attached to the aluminum extrusion anywhere along the T-slot with button-head or socket-head cap screws and T-nuts (furnished). Standard aluminum hinges and lift-off hinges are available. This specially designed hinge assembly is used on the light curtain swing-away mounting…
-
EX-AL™ Joining-and-Locking-Plates
$9.43 – $62.36A variety of brackets, plates, clamps, bolts, bearings, rollers, etc., are available for attaching guards to machines and for guard assemblies. Joining plates are used to connect extruded panels without additional machining. Joining strips and plates are used to connect extrusions to one another or to machines. The standard sizes of most of these mounting…
-
EX-AL™ Linear Bearings and Channel Guide
$49.30 – $130.53Linear bearings and channel guides are used in applications such as sliding panels or gates. These cost-effective alternatives to traditional bearings can be used in both low and high acceleration/deceleration applications. Linear bearings mate and glide on T-Slot aluminum extrusion profiles and the bearing pads are self-lubricating for smooth linear motion.
-
EX-AL™ Mounting Brackets
$25.38 – $97.16Mounting brackets are used for attaching extrusion-constructed guards to one another or to machines. The standard sizes of most of these mounting brackets are .188 thick 6063 aluminum alloy, clear anodized with .257 diameter holes on 1.0″ center lines.
-
EX-AL™ Panel Retainer (FKT560)
$30.82The panel retainer holds mesh in the extruded-aluminum framework of the guard. This retainer prevents panel push out and is the strongest way to hold panels in place.
-
EX-AL™ Perimeter Guarding Steel Hairpins
$0.00 – $21.76*PLEASE NOTE* The Hairpin Clip Assembly FKT753 is ordered separately. Steel hairpins are used in the adjustable area of a perimeter guarding panel and are constructed of black-oxidized steel. These hairpins are 1/4-inch round rods on 3/4-inch centers (1-inch wide from outside to outside) which create a 1/2-inch opening between hairpins). Hairpins provide adjustability of…
-
EX-AL™ T-Handle Hex Wrenches
$39.15 – $40.61The T-handle hex wrench is an ideal way to tighten and loosen button-head cap screws and socket-head cap screws. The handle has a cushion grip and the long arm (approx. 7 1/8″ arm / 9″ total w/handle) provides access to hard to reach areas. The end of the hex wrench is ball-shaped which allows for…
-
EX-AL™ T-Nuts, Fasteners and End Caps
$0.55 – $15.22EX-AL™ Various T-Nuts, Fasteners and End Caps T-nuts allow joining plates, panels, hinges, and other accessories to be bolted into the T-slot of any of the extrusions. They are made of hardened steel and are coated with corrosion-resistant black oxide. Standard T-nuts slide into the T-slot from the end. The drop-in style allows the T-nut…
-
Function-Testing Checklist for Perimeter Barrier Guards (LLL059)
$17.04This checklist can be used to function-test perimeter barrier guards. This should be done at every setup, operator, and shift change, as well as every time after maintenance is performed. The checklist is laminated and has a grommet in the corner so it can be attached to the barrier guard. The function-testing procedures are on…
-
Function-Testing Checklist for Point-of-Operation Barrier Guarding (LLL058)
$17.04Barrier guards should be function-tested at every setup, operator, and shift change, as well as every time after maintenance is performed. This point-of-operation barrier guard function-testing checklist can be used for this. It is laminated and has a grommet in the corner so it can be kept at the machine. The checklist has the function-testing…
-
Guard-Opening Scale – ANSI / CSA (KSC098)
$58.01An ANSI and CSA guard opening scale is a valuable tool to use during the design, installation, and inspection of guards to make sure they comply with ANSI and CSA safety standards. This folding guard opening scale is based on “A Review of Machine-Guarding Recommendations” by Donald R. Vaillancourt and Stover H. Snook of the…
-
Guard-Opening Scale – OSHA (KSC097)
$58.01An OSHA guard opening scale is a valuable tool to use during the design, installation, and inspection of guards to make sure they comply with OSHA’s Table O-10. This folding guard opening scale is based on Table O-10 of OSHA 29 CFR 1910.217 for mechanical power presses. It shows the distances that guards shall be…
-
EX-AL™ Hairpin Clip Assembly for Perimeter Guarding (FKT753)
$7.26The Hairpin Clip Assembly for Perimeter Guarding (FKT753) is designed for holding the hairpin ends and are essential in appropriate hairpin assembly.
-
Guard Opening Requirements Sign OSHA (KSC012)
$33.36This guard-opening sign is based on Table O-10 of OSHA 29 CFR 1910.217 for mechanical power presses, which shows the distances that guards shall be positioned from the point of operation based on opening size. This sign can be used by engineering, maintenance, etc., for reference when designing or fabricating guards. This 10″ x 12″…
-
-
Rubber Panel Gasket 10SERIES (GSKT10)
$0.51The rubber gasket tightly holds the poly-carbonate panels in the T-slot of the extruded aluminum. This gasket is made of high-grip rubber and is easily inserted into the T-slot after the panel is assembled in the frame. Poly-carbonate panels (3/16″-thick) are secured with the gasket on one side of the panel. The gasket material is…
-
-
-
Tower Light Assembly Control Box (LLD1631)
$404.64The tower light assembly control box provides a convenient means of mounting and wiring the tower light. The LLD1631 standard box comes with enough terminals to accommodate five (5) lights or four (4) lights with an alarm in the tower light assembly. This control box is approximately 8 inches x 6 inches x 6 inches.
Contact Customer Service Reach a Live Person @
Open Monday – Friday
8:00am – 5:00pm CST
Order Online Today
Let Us Help…
5795 Logistics Parkway
Rockford Illinois 61109
1-800-922-7533
customerservice@rockfordsystems.com
Our Mission
To reduce risk and prevent workplace
injuries by becoming our customer’s trusted
advisor and source for machine safeguarding
training, assessment services, and provider
of turnkey engineered safeguarding solutions.
Location
5795 Logistics Parkway
Rockford Illinois 61109
Phone
1-800-922-7533
Useful Links
Hours of Operation
Copyright 2023. All Rights Reserved By Rockford Systems LLC
